AUTONET TV

Don?t Meddle with the Pedal (Brake Caliper Replacement)

If you drive a newer vehicle, chances are it has disc brakes, and one of the components of that type of brake is called a brake caliper.  The caliper allows the pressure from your foot on the brake pedal to eventually move brake pads against discs in your wheels, which then slow and stop your vehicle.  

If you have disc brakes on all 4 wheels, your vehicle will have 4 calipers.  If you have them just on the front wheels, you’ll only have 2 calipers.  Because your wheels and brakes do their work outside and on the road surface, they are exposed to a lot of dirt and debris, as well as enduring heat, cold, moisture and tough treatment in daily driving.  

Your calipers have seals that are susceptible to the heat generated during the repetitive stops in normal driving, which can take a tough toll on those seals. If you drive when your vehicle’s brake pads and rotors are worn, you can ruin your calipers in the process.  

Here are a few signs that a caliper might be failing:  Your vehicle is pulling to one side when you apply the brakes.  Your pedal goes down to the floor when you push on it.  You hear squeaking from the wheels while braking.  You notice brake fluid on the pavement underneath your vehicle after you’ve parked it for a few hours.  

If you are getting any of those warning signs, it’s important to have one of our technicians determine what’s going on.  There are several brake components that contribute to your vehicle’s safe operation, including the calipers, pads, rotors, brake lines and brake fluid.  

Regular brake maintenance is recommended in your vehicle’s owner’s manual to prevent dangerous surprises.  And when you see issues, have your brakes serviced as soon as you see signs of trouble.

Gilmore's Auto Service
2151 N Broadway
Walnut Creek, CA 94596
(925) 939-9430
http://www.gilmoresauto.net

Straight to the Point (Alignment Signs of Problems)

It’s just common sense that your vehicle will drive better if all the wheels are lined up with each other and the road the way the engineers intended.  When they’re not, that is called being out of alignment.   Here are some signs that your alignment has problems.

• Your steering wheel isn’t straight when your vehicle goes straight down a straight road. This one’s pretty easy to notice.  If your vehicle’s logo on the wheel is tilted, that’s probably not the way designers wanted it to be. Bring it in and have us check it out.
• Your steering wheel is vibrating on a smooth road or when you are accelerating.  While this could be caused by several different things, one possibility is misalignment.  If your steering wheel is shaking, it should be examined by a trained technician.
• Your vehicle is pulling to one side without you wanting it to.  Sometimes the configuration of the road will cause it to pull slightly left or right.  But if you find yourself constantly correcting course to keep your vehicle headed straight down the road, that’s worth having us look at your alignment.
• You’re going through tires like there’s no tomorrow. The tread on your tires should be wearing nice and evenly from the outside to the inside of the tire.  If the wear isn’t even, it could be your vehicle needs an alignment.

We have equipment designed to quickly and accurately measure your vehicle’s alignment.  We can make precise adjustments to make sure you are headed straight where you want to go.  Have your alignment checked regularly. It can help prevent more serious problems in the future and make your vehicle drive as beautifully as you remember it used to.

Gilmore's Auto Service
2151 N Broadway
Walnut Creek, CA 94596
(925) 939-9430
http://www.gilmoresauto.net

Keeping Yourself in Suspension (Control Arm Assembly Replacement)

When you are pointing your vehicle straight down the street, it should go straight.  That’s pretty straightforward, right? Sometimes, though, you may notice you have to keep adjusting the steering wheel to keep going straight.  While that could be caused by many different issues, one possibility is that you have a failing or bent control arm.

Another sign is that when you brake, your vehicle pulls to one side or the other.  Sometimes your suspension may sound noisy, especially when you’re traveling on rough surfaces.  A damaged control arm may also make it almost impossible for you to get a good wheel alignment. 

The control arms are part of your suspension, and some vehicles have upper control arms and lower control arms.  Not all have the same number of control arms, but one thing is important: If you have worn bushings on your control arms or a worn-out ball joint, the control arm on the other side should also be replaced.  The rubber bushings are susceptible to damage from age and exposure to the elements, and ball joints usually shouldn’t be replaced separately. 

Any time you have a suspension issue, it’s important that a technician inspects the other parts of your suspension as well.  If one part of it is showing its age, it’s not unusual for other components to show similar wear.  

One other thing.  If you’ve had one of your control arms bent or damaged in an accident, you must have it replaced.  Your suspension is an important part of your vehicle’s safety and handling, so you should keep it in good operating condition.  After all, your life is riding on it, literally.   

Gilmore's Auto Service
2151 N Broadway
Walnut Creek, CA 94596
(925) 939-9430
http://www.gilmoresauto.net

Why Maintaining Your Windshield Wipers and Washers Matters (Windshield Wiper and Washer Inspection)

What do mud, bird droppings and frost all have in common? When they’re covering your windshield, they can temporarily obscure your view of the road, leaving you driving blind.  And when you can’t see the road clearly ahead of you, it can be really scary. 

That’s one of the reasons it’s important to maintain your windshield cleaning system, which includes your wipers, blades and washers.  They’re three vital components that work together to ensure you’re clearly seeing what’s going on with the road and drivers around you.

Your wipers are doing the physical work on the surface of your windshield’s glass.  The rubber or silicone is what touches the surface of the glass, and after time and exposure to the elements, wiper blades can get brittle, lose their flexibility, rip and tear to the point where they simply can’t clear the glass.  

What holds the wiper blades close to the glass is important, too.  Conventional blades use a metal frame which holds flexible rubber inserts.  Just the inserts can be changed which keeps replacement costs down.

Another type that’s gaining more popularity is called a beam blade.  It doesn’t have a frame but instead has a stiff beam and blade combination.  Beam blades can conform more snugly to the curved glass used in many recent vehicle designs.  Plus they have a sweeping shape which harnesses the pressure of the air that passes over them to apply more pressure during wiping, especially effective at highway speeds. High-tech rubber wiper blades, what …?! Seriously, they are pretty cool.

If you crossed the conventional frame blade with a beam blade, you’d have the hybrid wiper.  It’s constructed like a traditional wiper with a plastic frame that takes advantage of the aerodynamic shape of a beam blade.

Equally important to your windshield is the washer system since wiper blades simply don’t work on dry glass.  The washers use a pump to shoot fluid on your glass to remove debris, dust and other contaminants. 

All these systems need to always be at the ready since we never know what elements we’ll encounter on the road. Regular inspections and maintenance of your wipers and washers can ensure you’ll be able to see far down the road ahead of you for clearer vision and safer traveling.

Gilmore's Auto Service
2151 N Broadway
Walnut Creek, CA 94596
(925) 939-9430
http://www.gilmoresauto.net